Reasons Your Fiat 500 Key Fob Won't Work
A key fob for Fiat 500 makes it easy to open doors and start your vehicle. There are a variety of reasons why the fob could stop working. This could be due to a dead coin battery or damaged receiver module, water damage issues, and interfering.
This listing is for an new fiat 500 key fob replacement Fiat Flip Key Remote - look-alike Ilco brand that must be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes lock, unlock and programmers trunk buttons.
Dead Coin Battery
The most frequent reason that the 500 key fob won't function is an inactive battery. Modern key fobs have a very restricted operating range, and should be within some feet of the vehicle in order to function. If you are further away from your vehicle, and you press the keyfob button it will not respond, and display the message "Key Fob Not Detected".
If this happens, simply replace the battery on your coin cell (Part number CR2032) with a brand new one from a trusted brand like Panasonic, Duracell, or Energizer. You can typically find them in your local hardware store, or online.
You can test the battery on your coin-cell by pressing the buttons while you're standing close to your fiat 500 key button replacement 500. The parking lights should flash and the key fob will operate the lock and unlock switch.
If your key fob doesn't work even after replacing the battery, there may be water damage which is preventing it from interacting with the module inside your vehicle. Water damage can occur in a number of ways, ranging from an accidental splash to submerging the fob into salt water at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to pull the moisture out. If this does not work, you'll need to have your fob replaced by an auto locksmith or dealer.
Water Damage
Water damage can occur when you submerge the fob in the ocean or wash it in a washer. Saltwater is especially dangerous to the fob's circuit board, causing it to short out and eventually die. In the event that you let your fob get wet, it's not an ideal idea, but if you drop it into a cup of water or don't remember to remove it from your pocket before you run the washer, don't give up hope.
Take the battery off first. Clean the electronic chip using isopropyl or a similar product and then dry it completely before replacing the battery. Check the fob again to see if it is functioning. If the fob doesn't work, it may have to be reset. This is usually done by an auto locksmith or dealer.
If the key is older and was not programmed to your car it is likely to need to be replaced completely. A professional automotive locksmith will be able to complete this process. The locksmith needs to cut the key to match the ignition of your car. They'll also have to reprogram the fob in the car key cover fiat 500's system. This is a cheap and fast process that can be completed the same day.
Receiver Module Issues
The 500 key fob you have may not work because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far from your car, it won't respond to your commands. You can fix this by moving the remote closer to your vehicle until it responds.
If your fob won't work after you replace the coin battery, also called a "button", "watch" or "button" It may be due to a malfunction on the circuit board inside. In the majority of cases, reprogramming your fob can resolve the issue. You can find directions on how to do this for all vehicles by searching YouTube or looking through the owner's manual.
You may have to replace the metal clips that hold the coin battery in place. If they become loose, it could prevent your coin battery from sitting properly, causing your remote to malfunction.
In rare cases, the fob may become disconnected from your vehicle due to software issues or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain situations, they may need to reinstall the software on your body control module as well.
Interference
In addition to a dead coin battery, the key fob may not be able to receive or transmit an signal due to interference. This could happen if the key fob is near a radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob might not function include a poor connection to the buttons, damage to the internal chip, or water damage.
If the key fob has suddenly stopped working, without notice, or after trying everything you can do at home to resolve it e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module, which is located beneath the dashboard, receives radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.
Luckily, there is an easy method of resetting all on-board systems in your 500 keys, including the key fob. Disconnect the 12 volt battery for about 15 minutes by removing the negative cable and then the positive cable. Then reconnect the battery. This will remove any remaining electricity, and allow you to restart the computer in your car. This can help get your key fob to work again. If the problem persists you should consult an expert technician. They will be able to identify the root cause of any issues.
A key fob for Fiat 500 makes it easy to open doors and start your vehicle. There are a variety of reasons why the fob could stop working. This could be due to a dead coin battery or damaged receiver module, water damage issues, and interfering.
This listing is for an new fiat 500 key fob replacement Fiat Flip Key Remote - look-alike Ilco brand that must be programmed professionally by a local automotive locksmith (click here for Locksmith Search). This remote includes lock, unlock and programmers trunk buttons.
Dead Coin Battery
The most frequent reason that the 500 key fob won't function is an inactive battery. Modern key fobs have a very restricted operating range, and should be within some feet of the vehicle in order to function. If you are further away from your vehicle, and you press the keyfob button it will not respond, and display the message "Key Fob Not Detected".
If this happens, simply replace the battery on your coin cell (Part number CR2032) with a brand new one from a trusted brand like Panasonic, Duracell, or Energizer. You can typically find them in your local hardware store, or online.
You can test the battery on your coin-cell by pressing the buttons while you're standing close to your fiat 500 key button replacement 500. The parking lights should flash and the key fob will operate the lock and unlock switch.
If your key fob doesn't work even after replacing the battery, there may be water damage which is preventing it from interacting with the module inside your vehicle. Water damage can occur in a number of ways, ranging from an accidental splash to submerging the fob into salt water at the beach. If you suspect your fob was exposed to water, you can try placing it in a dry rice bag to pull the moisture out. If this does not work, you'll need to have your fob replaced by an auto locksmith or dealer.
Water Damage
Water damage can occur when you submerge the fob in the ocean or wash it in a washer. Saltwater is especially dangerous to the fob's circuit board, causing it to short out and eventually die. In the event that you let your fob get wet, it's not an ideal idea, but if you drop it into a cup of water or don't remember to remove it from your pocket before you run the washer, don't give up hope.
Take the battery off first. Clean the electronic chip using isopropyl or a similar product and then dry it completely before replacing the battery. Check the fob again to see if it is functioning. If the fob doesn't work, it may have to be reset. This is usually done by an auto locksmith or dealer.
If the key is older and was not programmed to your car it is likely to need to be replaced completely. A professional automotive locksmith will be able to complete this process. The locksmith needs to cut the key to match the ignition of your car. They'll also have to reprogram the fob in the car key cover fiat 500's system. This is a cheap and fast process that can be completed the same day.
Receiver Module Issues
The 500 key fob you have may not work because it's out of range. The remote usually has an area of 30 feet or less, and if it's too far from your car, it won't respond to your commands. You can fix this by moving the remote closer to your vehicle until it responds.
If your fob won't work after you replace the coin battery, also called a "button", "watch" or "button" It may be due to a malfunction on the circuit board inside. In the majority of cases, reprogramming your fob can resolve the issue. You can find directions on how to do this for all vehicles by searching YouTube or looking through the owner's manual.
You may have to replace the metal clips that hold the coin battery in place. If they become loose, it could prevent your coin battery from sitting properly, causing your remote to malfunction.
In rare cases, the fob may become disconnected from your vehicle due to software issues or hardware issues. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain situations, they may need to reinstall the software on your body control module as well.
Interference
In addition to a dead coin battery, the key fob may not be able to receive or transmit an signal due to interference. This could happen if the key fob is near a radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob might not function include a poor connection to the buttons, damage to the internal chip, or water damage.
If the key fob has suddenly stopped working, without notice, or after trying everything you can do at home to resolve it e.g. You could have a malfunctioning 500 receiver module after you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module, which is located beneath the dashboard, receives radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.
Luckily, there is an easy method of resetting all on-board systems in your 500 keys, including the key fob. Disconnect the 12 volt battery for about 15 minutes by removing the negative cable and then the positive cable. Then reconnect the battery. This will remove any remaining electricity, and allow you to restart the computer in your car. This can help get your key fob to work again. If the problem persists you should consult an expert technician. They will be able to identify the root cause of any issues.